Loading
Document Name
Sort Generated Document By
Total Credit Requested
$ 0.00
Preview
Create
Header Text
Total Credit Requested
$ 0.00
Preview
Create
Viewing:

1234 Main St.
Lookout Mountain, GA 30750
01/19/2020 9:00AM

Sample agent
agent

Agent Name

Agency Name
74
Items Inspected
7
Maintenance item
4
Recommendations

1 - Inspection Details

In Attendance
Client, Client's Agent, Home Owner
Occupancy
Furnished, Occupied
Temperature (approximate)
40 Fahrenheit (F)

34

Type of Building
Single Family
Weather Conditions
Clear

2 - Roof

IN NI NP R
2.1 Coverings X
2.2 Skylights, Chimneys & Other Roof Penetrations X
2.3 Flashings X
2.4 Eaves, Soffits & Fascia X
2.5 Gutters & Downspouts X
Roof Type/Style
Combination
Coverings: Material
Asphalt
Flashings: Material
Aluminum
Gutters & Downspouts: Gutter Material
Aluminum
Inspection Method
Camera/Telescoping Pole

I. The inspector shall inspect from ground level or the eaves: A. the roof-covering materials; B. the gutters; C. the downspouts; D. the vents, flashing, skylights, chimney, and other roof penetrations; and E. the general structure of the roof from the readily accessible panels, doors or stairs. II. The inspector shall describe: A. the type of roof-covering materials. III. The inspector shall report as in need of correction: A. observed indications of active roof leaks. IV. The inspector is not required to: A. walk on any roof surface. B. predict the service life expectancy. C. inspect underground downspout diverter drainage pipes. D. remove snow, ice, debris or other conditions that prohibit the observation of the roof surfaces. E. move insulation. F. inspect antennae, satellite dishes, lightning arresters, de-icing equipment, or similar attachments. G. walk on any roof areas that appear, in the inspectors opinion, to be unsafe. H. walk on any roof areas if doing so might, in the inspector's opinion, cause damage. I. perform a water test. J. warrant or certify the roof. K. confirm proper fastening or installation of any roof-covering material.

  • IN = Inspected
  • NI = Not Inspected
  • NP = Not Present
  • R = Recommendations
$
Credit
Comment
2.4.1 - Eaves, Soffits & Fascia

Fascia/Soffit - Minor Damage
South Gable

Sections of fascia and soffit at roof gable eaves showed minor rot.   Not an immediate concern but will need replacement in near future.  

Contractor Qualified Professional
$
Credit
Comment
2.4.2 - Eaves, Soffits & Fascia

Paint/Finish Failing - Minor
West Fascia

The paint or finish is failing. This can lead to deterioration and rot of the material. Recommend that the araes be properly prepared and painted / finished.

Paint roller Painting Contractor

3 - Exterior

IN NI NP R
3.1 Electrical Service Entrance Conductors X
3.2 Exterior Windows X
3.3 Exterior Doors X
3.4 Siding, Flashing & Trim X
3.5 Walkways, Patios & Driveways X
3.6 Decks, Balconies, Porches & Steps X
3.7 Vegetation, Grading, Drainage & Retaining Walls X
Inspection Method
Visual
Siding, Flashing & Trim: Siding Style
Lap Siding
Decks, Balconies, Porches & Steps: Appurtenance
Covered Porch, Deck with Steps, Retaining Wall
Electrical Service Entrance Conductors: Electrical Service Conductors
Overhead, 220 Volts
Exterior Windows: General
Exterior Doors: Exterior Entry Doors
Wood, Metal, Glass
Siding, Flashing & Trim: Siding Material
Wood
Walkways, Patios & Driveways: Driveway Material
Stone, Concrete
Decks, Balconies, Porches & Steps: Material
Concrete, Wood
Vegetation, Grading, Drainage & Retaining Walls: General

I. The inspector shall inspect: A. the exterior wall-covering materials, flashing and trim; B. all exterior doors; C. adjacent walkways and driveways; D. stairs, steps, stoops, stairways and ramps; E. porches, patios, decks, balconies and carports; F. railings, guards and handrails; G. the eaves, soffits and fascia; H. a representative number of windows; and I. vegetation, surface drainage, retaining walls and grading of the property, where they may adversely affect the structure due to moisture intrusion. II. The inspector shall describe: A. the type of exterior wall-covering materials. III. The inspector shall report as in need of correction: A. any improper spacing between intermediate balusters, spindles and rails. IV. The inspector is not required to: A. inspect or operate screens, storm windows, shutters, awnings, fences, outbuildings, or exterior accent lighting. B. inspect items that are not visible or readily accessible from the ground, including window and door flashing. C. inspect or identify geological, geotechnical, hydrological or soil conditions. D. inspect recreational facilities or playground equipment. E. inspect seawalls, breakwalls or docks. F. inspect erosion-control or earth-stabilization measures. G. inspect for safety-type glass. H. inspect underground utilities. I. inspect underground items. J. inspect wells or springs. K. inspect solar, wind or geothermal systems. L. inspect swimming pools or spas. M. inspect wastewater treatment systems, septic systems or cesspools. N. inspect irrigation or sprinkler systems. O. inspect drainfields or dry wells. P. determine the integrity of multiple-pane window glazing or thermal window seals.

  • IN = Inspected
  • NI = Not Inspected
  • NP = Not Present
  • R = Recommendations
$
Credit
Comment
3.2.1 - Exterior Windows

Screens Missing
General

Screens were missing on more than half of windows.  

$
Credit
Comment
3.5.1 - Walkways, Patios & Driveways

Driveway Cracking

Cracking of driveway present.  Recommend monitoring for further cracking and repair as needed.  

Contractor Qualified Professional
$
Credit
Comment
3.5.2 - Walkways, Patios & Driveways

Fence Leaning

Chain link fence damaged. 

Contractor Qualified Professional
$
Credit
Comment
3.6.1 - Decks, Balconies, Porches & Steps

Cracks/Gaps
Front & Side Porch

Recommend sealing cracked areas and any gaps present.  

Wrench DIY
$
Credit
Comment
3.7.1 - Vegetation, Grading, Drainage & Retaining Walls

Negative Grading
West/Front

Grading is sloping towards front of structure. Ideally, ground should slope away from structure at a ratio of 6 over 10.  Any deficiencies as a result of negative grading will be noted in crawlspace section of report.  

4 - Basement, Foundation, Crawlspace & Structure

IN NI NP R
4.1 Foundation X
4.2 Basements & Crawlspaces X
4.3 Floor Structure X
4.4 Vapor Retarders (Crawlspace or Basement) X
Foundation: Material
Brick, Masonry Block, Beam And Pier
Basements & Crawlspaces: Basement/Crawlspace Floor
Dirt
Floor Structure: Material
Wood Joists
Floor Structure: Sub-floor
OSB
Floor Structure: Flooring Insulation
Fiberglass
Inspection Method
Inside Crawlspace

I. The inspector shall inspect: A. the foundation; B. the basement; C. the crawlspace; and D. structural components. II. The inspector shall describe: A. the type of foundation; and B. the location of the access to the under-floor space. III. The inspector shall report as in need of correction: A. observed indications of wood in contact with or near soil; B. observed indications of active water penetration; C. observed indications of possible foundation movement, such as sheetrock cracks, brick cracks, out-of-square door frames, and unlevel floors; and D. any observed cutting, notching and boring of framing members that may, in the inspector's opinion, present a structural or safety concern. IV. The inspector is not required to: A. enter any crawlspace that is not readily accessible, or where entry could cause damage or pose a hazard to him/herself. B. move stored items or debris. C. operate sump pumps with inaccessible floats. D. identify the size, spacing, span or location or determine the adequacy of foundation bolting, bracing, joists, joist spans or support systems. E. provide any engineering or architectural service. F. report on the adequacy of any structural system or component.

  • IN = Inspected
  • NI = Not Inspected
  • NP = Not Present
  • R = Recommendations
$
Credit
Comment
4.3.1 - Floor Structure

Joists Need Repair
Crawlspace NW & SW

One or more floor joists were damaged and in need of repair/reinforcement. 

Wrenches Handyman
$
Credit
Comment
4.3.2 - Floor Structure

Termite Activity/Damage
General

Termite damage noted in isolated areas appeared to be inactive. Recommend treatment as a precautionary measure. New joist and beam work have been installed at areas were most severe damage was present.

Contractor Qualified Professional

5 - Electrical

IN NI NP R
5.1 Main & Subpanels, Service & Grounding, Main Overcurrent Device X
5.2 Branch Wiring Circuits, Breakers & Fuses X
5.3 Lighting Fixtures, Switches & Receptacles X
5.4 GFCI & AFCI X
5.5 Smoke Detectors X
5.6 Carbon Monoxide Detectors X
Main & Subpanels, Service & Grounding, Main Overcurrent Device: Main Panel Location
Basement
Main & Subpanels, Service & Grounding, Main Overcurrent Device: Panel Manufacturer
Square D
Main & Subpanels, Service & Grounding, Main Overcurrent Device: Panel Type
Circuit Breaker
Branch Wiring Circuits, Breakers & Fuses: Branch Wire
Copper, Stranded Copper
Branch Wiring Circuits, Breakers & Fuses: Wiring Method
Romex
Main & Subpanels, Service & Grounding, Main Overcurrent Device: Panel Capacity
200 AMP

I. The inspector shall inspect: A. the service drop; B. the overhead service conductors and attachment point; C. the service head, gooseneck and drip loops; D. the service mast, service conduit and raceway; E. the electric meter and base; F. service-entrance conductors; G. the main service disconnect; H. panelboards and over-current protection devices (circuit breakers and fuses); I. service grounding and bonding; J. a representative number of switches, lighting fixtures and receptacles, including receptacles observed and deemed to be arc-fault circuit interrupter (AFCI)-protected using the AFCI test button, where possible; K. all ground-fault circuit interrupter receptacles and circuit breakers observed and deemed to be GFCIs using a GFCI tester, where possible; and L. smoke and carbon-monoxide detectors. II. The inspector shall describe: A. the main service disconnect's amperage rating, if labeled; and B. the type of wiring observed. III. The inspector shall report as in need of correction: A. deficiencies in the integrity of the serviceentrance conductors insulation, drip loop, and vertical clearances from grade and roofs; B. any unused circuit-breaker panel opening that was not filled; C. the presence of solid conductor aluminum branch-circuit wiring, if readily visible; D. any tested receptacle in which power was not present, polarity was incorrect, the cover was not in place, the GFCI devices were not properly installed or did not operate properly, evidence of arcing or excessive heat, and where the receptacle was not grounded or was not secured to the wall; and E. the absence of smoke detectors. IV. The inspector is not required to: A. insert any tool, probe or device into the main panelboard, sub-panels, distribution panelboards, or electrical fixtures. B. operate electrical systems that are shut down. C. remove panelboard cabinet covers or dead fronts. D. operate or re-set over-current protection devices or overload devices. E. operate or test smoke or carbon-monoxide detectors or alarms F. inspect, operate or test any security, fire or alarms systems or components, or other warning or signaling systems. G. measure or determine the amperage or voltage of the main service equipment, if not visibly labeled. H. inspect ancillary wiring or remote-control devices. I. activate any electrical systems or branch circuits that are not energized. J. inspect low-voltage systems, electrical de-icing tapes, swimming pool wiring, or any timecontrolled devices. K. verify the service ground. L. inspect private or emergency electrical supply sources, including, but not limited to: generators, windmills, photovoltaic solar collectors, or battery or electrical storage facility. M. inspect spark or lightning arrestors. N. inspect or test de-icing equipment. O. conduct voltage-drop calculations. P. determine the accuracy of labeling. Q. inspect exterior lighting.

  • IN = Inspected
  • NI = Not Inspected
  • NP = Not Present
  • R = Recommendations

6 - Heating

IN NI NP R
6.1 Equipment X
6.2 Normal Operating Controls X
6.3 Distribution Systems X
6.4 Vents, Flues & Chimneys X
6.5 Presence of Installed Heat Source in Each Room X
Equipment: Energy Source
Electric, Gas
Equipment: Heat Type
Heat Pump, Forced Air, Gas-Fired Heat
Equipment: Approximate Age
4 Yrs
Equipment: Brand
Goodman
Distribution Systems: Ductwork
Insulated
Vents, Flues & Chimneys: Inspected

I. The inspector shall inspect: A. the heating system, using normal operating controls. II. The inspector shall describe: A. the location of the thermostat for the heating system; B. the energy source; and C. the heating method. III. The inspector shall report as in need of correction: A. any heating system that did not operate; and B. if the heating system was deemed inaccessible. IV. The inspector is not required to: A. inspect or evaluate the interior of flues or chimneys, fire chambers, heat exchangers, combustion air systems, fresh-air intakes, humidifiers, dehumidifiers, electronic air filters, geothermal systems, or solar heating systems. B. inspect fuel tanks or underground or concealed fuel supply systems. C. determine the uniformity, temperature, flow, balance, distribution, size, capacity, BTU, or supply adequacy of the heating system. D. light or ignite pilot flames. E. activate heating, heat pump systems, or other heating systems when ambient temperatures or other circumstances are not conducive to safe operation or may damage the equipment. F. override electronic thermostats. G. evaluate fuel quality. H. verify thermostat calibration, heat anticipation, or automatic setbacks, timers, programs or clocks.

  • IN = Inspected
  • NI = Not Inspected
  • NP = Not Present
  • R = Recommendations
$
Credit
Comment
6.1.1 - Equipment

Insulation Missing
Crawlspace

Insulation fell short of unit leaving a small portion of refrigerant line exposed which can cause condensation and deterioration of unit.  Recommend insulating around exposed area.  

Wrench DIY
$
Credit
Comment
6.3.1 - Distribution Systems

Minor Damage
Crawlspace West

Minor damage to insulation around ductwork.  Recommend repair with duct/aluminum tape to avoid further damage/ loss of efficiency/ condensation.  

Wrench DIY

7 - Cooling

IN NI NP R
7.1 Cooling Equipment X
7.2 Normal Operating Controls X
7.3 Distribution System X
7.4 Presence of Installed Cooling Source in Each Room X
Cooling Equipment: Energy Source/Type
Electric
Cooling Equipment: Location
Exterior North
Cooling Equipment: Approximate Age
4 Yrs
Cooling Equipment: Dual System

Dual system controls second and main story separately.  

Distribution System: Configuration
Split
Distribution System: Ductwork
Insulated
Distribution System: See Heating for Ductwork
Cooling Equipment: Brand
Goodman

I. The inspector shall inspect: A. the cooling system, using normal operating controls. II. The inspector shall describe: A. the location of the thermostat for the cooling system; and B. the cooling method. III. The inspector shall report as in need of correction: A. any cooling system that did not operate; and B. if the cooling system was deemed inaccessible. IV. The inspector is not required to: A. determine the uniformity, temperature, flow, balance, distribution, size, capacity, BTU, or supply adequacy of the cooling system. B. inspect portable window units, through-wall units, or electronic air filters. C. operate equipment or systems if the exterior temperature is below 65 Fahrenheit, or when other circumstances are not conducive to safe operation or may damage the equipment. D. inspect or determine thermostat calibration, cooling anticipation, or automatic setbacks or clocks. E. examine electrical current, coolant fluids or gases, or coolant leakage.

  • IN = Inspected
  • NI = Not Inspected
  • NP = Not Present
  • R = Recommendations

8 - Bathrooms

IN NI NP R
8.1 Toilets X
8.2 Sinks, Showers, Tubs X
8.3 Floors, Trim, Cabinetry X
8.4 GFCIs X
8.5 Exhaust Systems X
Exhaust Systems: Exhaust Fans
Fan Only
Toilets: Inspected

Attempted to flush all toilets.

Inspected seals and tank-to-bowl connections on toilets.  

Inspected base to flange connection at toilets by applying force to side of bowl.   

Sinks, Showers, Tubs: Inspected

Ran water at sinks, showers and tubs.  

Inspected tub and shower surrounds and shower floors for areas of potential moisture intrusion.  

Floors, Trim, Cabinetry : Inspected

Flooring, cabinets, trim, fixtures and finishes were inspected.  

  • IN = Inspected
  • NI = Not Inspected
  • NP = Not Present
  • R = Recommendations

9 - Plumbing

IN NI NP R
9.1 Drain, Waste, & Vent Systems X
9.2 Water Supply & Distribution X
9.3 Hot Water Systems, Controls, Flues & Vents X
9.4 Fuel Storage & Distribution Systems X
Water Supply & Distribution: Water Source
Public
Water Supply & Distribution: Water Supply Material
Pex
Water Supply & Distribution: Main Shutoff Location
Crawlspace, North
Hot Water Systems, Controls, Flues & Vents: Power Source/Type
Gas, Tankless
Hot Water Systems, Controls, Flues & Vents: Location
Crawlspace, Basement
Hot Water Systems, Controls, Flues & Vents: Approximate Age
4 Yrs
Fuel Storage & Distribution Systems: Main Gas Shut-off Location
Gas Meter
Drain, Waste, & Vent Systems: Material
PVC
Water Supply & Distribution: Distribution Material
Pex
Hot Water Systems, Controls, Flues & Vents: Manufacturer
Navien

I recommend flushing & servicing your water heater tank annually for optimal performance. Water temperature should be set to at least 120 degrees F to kill microbes and no higher than 130 degrees F to prevent scalding. 

Here is a nice maintenance guide from Lowe's to help. 

I. The inspector shall inspect: A. the main water supply shut-off valve; B. the main fuel supply shut-off valve; C. the water heating equipment, including the energy source, venting connections, temperature/pressure-relief (TPR) valves, Watts 210 valves, and seismic bracing; D. interior water supply, including all fixtures and faucets, by running the water; E. all toilets for proper operation by flushing; F. all sinks, tubs and showers for functional drainage; G. the drain, waste and vent system; and H. drainage sump pumps with accessible floats. II. The inspector shall describe: A. whether the water supply is public or private based upon observed evidence; B. the location of the main water supply shut-off valve; C. the location of the main fuel supply shut-off valve; D. the location of any observed fuel-storage system; and E. the capacity of the water heating equipment, if labeled. III. The inspector shall report as in need of correction: A. deficiencies in the water supply by viewing the functional flow in two fixtures operated simultaneously; B. deficiencies in the installation of hot and cold water faucets; C. mechanical drain stops that were missing or did not operate if installed in sinks, lavatories and tubs; and D. toilets that were damaged, had loose connections to the floor, were leaking, or had tank components that did not operate. IV. The inspector is not required to: A. light or ignite pilot flames. B. measure the capacity, temperature, age, life expectancy or adequacy of the water heater. C. inspect the interior of flues or chimneys, combustion air systems, water softener or filtering systems, well pumps or tanks, safety or shut-off valves, floor drains, lawn sprinkler systems, or fire sprinkler systems. D. determine the exact flow rate, volume, pressure, temperature or adequacy of the water supply. E. determine the water quality, potability or reliability of the water supply or source. F. open sealed plumbing access panels. G. inspect clothes washing machines or their connections. H. operate any valve. I. test shower pans, tub and shower surrounds or enclosures for leakage or functional overflow protection. J. evaluate the compliance with conservation, energy or building standards, or the proper design or sizing of any water, waste or venting components, fixtures or piping. K. determine the effectiveness of anti-siphon, backflow prevention or drain-stop devices. L. determine whether there are sufficient cleanouts for effective cleaning of drains. M. evaluate fuel storage tanks or supply systems. N. inspect wastewater treatment systems. O. inspect water treatment systems or water filters. P. inspect water storage tanks, pressure pumps, or bladder tanks. Q. evaluate wait time to obtain hot water at fixtures, or perform testing of any kind to water heater elements. R. evaluate or determine the adequacy of combustion air. S. test, operate, open or close: safety controls, manual stop valves, temperature/pressure-relief valves, control valves, or check valves. T. examine ancillary or auxiliary systems or components, such as, but not limited to, those related to solar water heating and hot water circulation. U. determine the existence or condition of polybutylene plumbing. V. inspect or test for gas or fuel leaks, or indications thereof.

  • IN = Inspected
  • NI = Not Inspected
  • NP = Not Present
  • R = Recommendations

10 - Doors, Windows & Interior

IN NI NP R
10.1 Doors X
10.2 Windows X
10.3 Floors X
10.4 Walls X
10.5 Ceilings X
10.6 Steps, Stairways & Railings X
Doors: Inspected
Windows: Window Type
Single-hung
Windows: New Windows Installed
Windows: Window Material
Vinyl
Floors: Floor Coverings
Hardwood, Tile, Vinyl
Walls: Inspected
Ceilings: Inspected
Steps, Stairways & Railings: Inspected

I. The inspector shall inspect: A. a representative number of doors and windows by opening and closing them; B. floors, walls and ceilings; C. stairs, steps, landings, stairways and ramps; D. railings, guards and handrails; and E. garage vehicle doors and the operation of garage vehicle door openers, using normal operating controls. II. The inspector shall describe: A. a garage vehicle door as manually-operated or installed with a garage door opener. III. The inspector shall report as in need of correction: A. improper spacing between intermediate balusters, spindles and rails for steps, stairways, guards and railings; B. photo-electric safety sensors that did not operate properly; and C. any window that was obviously fogged or displayed other evidence of broken seals. IV. The inspector is not required to: A. inspect paint, wallpaper, window treatments or finish treatments. B. inspect floor coverings or carpeting. C. inspect central vacuum systems. D. inspect for safety glazing. E. inspect security systems or components. F. evaluate the fastening of islands, countertops, cabinets, sink tops or fixtures. G. move furniture, stored items, or any coverings, such as carpets or rugs, in order to inspect the concealed floor structure. H. move suspended-ceiling tiles. I. inspect or move any household appliances. J. inspect or operate equipment housed in the garage, except as otherwise noted. K. verify or certify the proper operation of any pressure-activated auto-reverse or related safety feature of a garage door. L. operate or evaluate any security bar release and opening mechanisms, whether interior or exterior, including their compliance with local, state or federal standards. M. operate any system, appliance or component that requires the use of special keys, codes, combinations or devices. N. operate or evaluate self-cleaning oven cycles, tilt guards/latches, or signal lights. O. inspect microwave ovens or test leakage from microwave ovens. P. operate or examine any sauna, steamgenerating equipment, kiln, toaster, ice maker, coffee maker, can opener, bread warmer, blender, instant hot-water dispenser, or other small, ancillary appliances or devices. Q. inspect elevators. R. inspect remote controls. S. inspect appliances. T. inspect items not permanently installed. U. discover firewall compromises. V. inspect pools, spas or fountains. W. determine the adequacy of whirlpool or spa jets, water force, or bubble effects. X. determine the structural integrity or leakage of pools or spas.

  • IN = Inspected
  • NI = Not Inspected
  • NP = Not Present
  • R = Recommendations

11 - Kitchen & Built In Appliances

IN NI NP R
11.1 Countertops & Cabinets X
11.2 Sinks X
11.3 Food Waste Disposals X
11.4 Dishwasher X
11.5 Refrigerator X
11.6 Range/Oven/Cooktop X
11.7 Built-in Microwave X
Range/Oven/Cooktop: Range/Oven Energy Source
Gas
Photos
Countertops & Cabinets: Countertop Material
Marble
Countertops & Cabinets: Cabinetry
Wood
Sinks: Inspected
Dishwasher: Brand
Frigidaire
Refrigerator: Brand
GE
Range/Oven/Cooktop: Range/Oven Brand
Frigidaire
Range/Oven/Cooktop: Exhaust Hood Type
Vented
Built-in Microwave: Inspected
Dishwasher: Dishwasher Full - Not Tested

10.1 The inspector shall inspect: F. installed ovens, ranges, surface cooking appliances, microwave ovens, dishwashing machines, and food waste grinders by using normal operating controls to activate the primary function. 10.2 The inspector is NOT required to inspect: G. installed and free-standing kitchen and laundry appliances not listed in Section 10.1.F. H. appliance thermostats including their calibration, adequacy of heating elements, self cleaning oven cycles, indicator lights, door seals, timers, clocks, timed features, and other specialized features of the appliance. I. operate, or con rm the operation of every control and feature of an inspected appliance.

  • IN = Inspected
  • NI = Not Inspected
  • NP = Not Present
  • R = Recommendations

12 - Attic, Insulation & Ventilation

IN NI NP R
12.1 Roof Structure & Attic X
12.2 Vent Penetrations X
12.3 Attic Insulation X
12.4 Ventilation X
12.5 Exhaust Systems X
Roof Structure & Attic: Material
Planks, OSB
Roof Structure & Attic: Type
Combination
Attic Insulation: Insulation Type
Blown, Cellulose
Attic Insulation: Avgerage Depth
Attic
12 Inches
Ventilation: Ventilation Type
Soffit Vents, Gable Vents
Photos

I. The inspector shall inspect: A. insulation in unfinished spaces, including attics, crawlspaces and foundation areas; B. ventilation of unfinished spaces, including attics, crawlspaces and foundation areas; and C. mechanical exhaust systems in the kitchen, bathrooms and laundry area. II. The inspector shall describe: A. the type of insulation observed; and B. the approximate average depth of insulation observed at the unfinished attic floor area or roof structure. III. The inspector shall report as in need of correction: A. the general absence of insulation or ventilation in unfinished spaces. IV. The inspector is not required to: A. enter the attic or any unfinished spaces that are not readily accessible, or where entry could cause damage or, in the inspector's opinion, pose a safety hazard. B. move, touch or disturb insulation. C. move, touch or disturb vapor retarders. D. break or otherwise damage the surface finish or weather seal on or around access panels or covers. E. identify the composition or R-value of insulation material. F. activate thermostatically operated fans. G. determine the types of materials used in insulation or wrapping of pipes, ducts, jackets, boilers or wiring. H. determine the adequacy of ventilation.

  • IN = Inspected
  • NI = Not Inspected
  • NP = Not Present
  • R = Recommendations

13 - Laundry

IN NI NP R
13.1 Dryer Power Source X
13.2 Dryer Vent X
13.3 Washer Hookups X
Dryer Power Source: Type
220V
Dryer Vent: Type
Rigid Metal, Flexible Metal, Vents To Exterior
Washer Hookups: Inspected
Photos
  • IN = Inspected
  • NI = Not Inspected
  • NP = Not Present
  • R = Recommendations